Restore windows vista os

If you reset your computer back to factory condition you will also have to restore all your personal files from a backup, remove all the outdated third-party software installed at the factory that is no longer supported e. If you would like to tell us what problems you are currently encountering on you computer we might be able to provide a solution that doesn't require something as drastic as a factory reset or clean reinstall of your operating system.

If you require further assistance please start Internet Explorer 9 , go to Help About Internet Explorer, and let us know your current Update Versions see image below.

If you have Update Versions 9. I have the same question Report abuse. Details required :. Cancel Submit. Bill Smithers Volunteer Moderator. This is what you used: As the computer restarts, press the F8 key until the Advanced Boot Options menu appears on the screen. With a Desktop it is either on the side, rear or top of the Computer Case. How satisfied are you with this reply?

If the restored computer was a member computer or member server, test the security channel by using the NLTEST command:.

If the destination computer is a member computer or member server, you may have to reset its security channel with the domain, depending on how recently the backup occurred. The netdiag command is available when you install the Support Tools on the Windows installation media. Warning The following procedure is intended for failure recovery or hardware replacement of a single domain when no other domain controllers are available. If there are other healthy domain controllers online for the domain, we recommend that you do not perform a restore at all.

Instead, perform a new installation of Windows on the destination computer and run the Active Directory Installation Wizard Dcpromo. Note The following requirements must be met to move Windows Server to a different computer.

Startup hard disk capacity should be larger or same size. You should make sure that your RAID setup on destination computer does not interfere with the boot order of the hard disks. Additionally, the architecture of WinRE or Setup CD should match architecture of the operating system being recovered. You can treat AMD or Intel processors as being the same, if they follow the same architecture. The backup of AMD x64 computer's operating system can be recovered on to an Intel x64 computer or vice a versa.

To back up and restore a Windows Server domain controller installation, follow the steps in the following TechNet article:. Backing up your Server. Use the Windows backup tool to back up the system drive and the system state.

For Windows , if Sysvol resides on a drive other than the system drive, you must also back up that folder and all subfolders. Perform a new installation of Windows on the destination computer by using the same version of Windows as the source computer. Make sure that you install Windows to the same location as on the source computer. After the new installation is complete, log on to the destination computer as an administrator.

By using Disk Management, create, format, and assign drive letters to any additional volumes that may be required to hold a system state component or an application. Put a copy of the Boot. If the source computer is the only domain controller for the domain, reinstall Windows on the source computer, or disconnect it from the network, before you restore the backup to the destination computer. We recommend those steps, because it is too easy for someone to turn the source computer back on.

If someone turns on the source computer, name conflicts or other problems with the destination computer occur. If the source computer is not the only domain controller for the domain, use the Active Directory Installation Wizard to remove Active Directory from the source computer.

Then, either reinstall Windows on the source computer, or disconnect it from the network. When you have confirmed that the source computer and the restored destination computer are not online at the same time, restore the backup by following these steps:. Restore the system state and the system drive from the backup that you performed earlier.

For Windows , you must also manually select the Sysvol folder to be restored. The system state includes Sysvol. However, there is an issue in Windows that prevents the Sysvol junction points from being restored correctly if you restore only the system state. Make sure that you select the option to restore to Original location.

Replace the Boot. When the restore operation is complete, and when you have verified that the destination computer is functioning correctly, you can configure the server to use itself for DNS. If the destination computer will be the first or only domain controller for the domain, follow these steps to authoritatively restore the File Replication Service FRS.

This step must also be complete before the first restart after the restore operation is complete. Warning Do not follow these steps if there are existing domain controllers in the domain. Click Start , and then click Run , type regedit, and then press Enter. Find the subkey of the Cumulative Replica Sets subkey that matches the name of the subkey from the previous step. Expand Cumulative Replica Sets , click the subkey that represents the Sysvol replica set, and then double-click BurFlags.

Restart the computer and verify that it is functioning correctly by using the dcdiag and netdiag commands. For more information about how to use the dcdiag command, click the following article number to view the article in the Microsoft Knowledge Base:. If the trust relationship test result indicates that the test was skipped, you can safely ignore the results.

This result indicates that the computer that you are running the test on has the PDC emulator operation master role. If the trust relationship test fails, you have a failed security channel. To fix this, run the netdom command on the destination computer to reset the security channel. To reset the security channel on a domain controller by using the netdom command, follow these steps:. The command must be running locally on the destination computer. Make sure that you verify that replication is working if there are existing domain controllers in the domain.

For more information about how to verify replication, click the following article number to view the article in the Microsoft Knowledge Base:. The computer that is running Windows Server crashes on startup. The computer spontaneously restarts when you receive the following message on a black screen early in the restart process:. To resolve issues with the display settings or with a network adapter, remove the graphics adapter or the network adapter from Device Manager, and then restart the computer.

Windows will redetect the device and possibly prompt you for drivers. Click Start , right-click Command Prompt , and then click Run as administrator. To resolve the Stop error or the problem where a computer stops responding, perform an in-place upgrade of Windows. For more information about how to perform an in-place upgrade, click the following article numbers to view the articles in the Microsoft Knowledge Base:.

To do this, follow these steps:. Click Start , click Run , type regedit, and then click OK. Locate and then right-click the following registry subkey. If the ClientProtocols subkey itself is missing, add it under the Rpc subkey. If values are missing in the ClientProtocols subkey, follow these steps:. Right-click the value name that you typed in step B, and then click Modify. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy.

Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article methods. Tips and Warnings. Related Articles. Author Info Last Updated: September 16, Method 1. Select the radio button next to the restore point for which you want your computer restored. You can either choose the restore point recommended by Windows, or choose a different restore point.

Method 2. Click on the Start menu, then click on the arrow next to the Lock icon. Click on the name of the operating system you want repaired. Select the restoration point to which you want your computer restored. Method 3. Power on your Windows Vista computer. Press the F8 key repeatedly as your computer boots up. The Advanced Boot Options menu will display on-screen. If the Advanced Boot Options menu does not display, restart your computer and continue to press F8 repeatedly before the Windows logo displays on-screen.

Select your username from the dropdown menu and type your Windows Vista password. Choose the restoration point to which you want the state of your computer restored. Method 4. Insert your Windows Vista Installation disc into the disc drive of your computer.

Method 5. Disconnect all non-essential external peripherals from your computer. Examples of non-essential external peripherals are printers, flash drives, and scanners.