Stiga park pro 16 parts manual

When washing the machine with water under high pressure, do not point the jet directly at the transmission. Do not point jets of water directly at the engine. Use a brush or compressed air in order to clean it. Change oil when the engine is warm. Change the oil more often after 25 hours of operation or at least once a season if the engine has to operate under demanding conditions or if the ambient temperature is high.

The engine oil may be very hot if it is drained off directly after the engine is shut off. So allow the engine to cool a few minutes before draining the oil. Oil drain pipe metal : Unscrew the oil drain plug at the end of the pipe.

Then take the oil to a recycling station. Do not allow oil to get on the V-belts. Unless otherwise stated, all service and maintenance must be carried out on a stationary machine when the engine is not running. Screw in the oil drain plug. Make sure that the fibre gasket and the O-ring inside the plug are not damaged and that they are in the correct place.

Prevent the machine from rolling by always applying the parking brake. Remove the dipstick and fill up with new oil. Oil capacity: Comfort, President - 1. However, oil consumption may increase somewhat if 10W is used. Therefore, check the oil level more regularly if you use this type of oil. Use oil without any additives. Do not fill with too much oil. This can cause the engine to overheat. After filling up the oil, start the engine and idle for 30 seconds. Stop the engine. Wait for 30 seconds and then check the oil level.

Check to see if there is any oil leakage. Unscrew the oil drain plug at the end of the pipe fig. Collect the oil in a collection vessel. Before screwing the new filter, oil the filter gasket with engine oil. Screw the filter by hand, until the filter gasket touches the filter attachment. Start the engine and idle to see if any leakage occurs. Check the oil level.

Clean the paper filter insert once a year or after every hours of operation, whichever comes first. Royal: Clean the air filter every 3 months or after every 50 hours of operation, whichever comes first.

All models: Note! Both filters should be cleaned more often if the machine operates on dusty ground. Remove the protective cover of the air filter fig. Dismantle the paper filter insert and the foam pre-filter. Make sure that no dirt gets into the carburettor. Clean the air filter housing. Oil capacity: Royal - 0. In total the engine holds 1. Pro 16, Pro Wash the pre-filter in liquid detergent and water. Squeeze dry. Pour a little oil on the filter and squeeze in the oil. Oil type for all seasons: SAE 10W President, Comfort: Replace the pre-filter once a year or after every 25 hours of operation, whichever comes first.

Clean the paper filter insert as follows: Knock it lightly against a flat surface. Assemble in the reverse order. On delivery, the battery is in the accessories box. Petroleum-based solvents such as kerosene may not be used for cleaning the paper filter insert.

These solvents can destroy the filter. Do not use compressed air for cleaning the paper filter insert. The paper filter insert must not be oiled. Remove the cover by pressing in the locking mechanism with a screwdriver etc. Remove the foam filter and wash it in liquid detergent and water. Do not oil the filter. Replace the filter and snap the cover into place.

Clean the spark plug after every hours of operation or once a season. For replacing a spark plug, a spark plug sleeve A and a torsion pin B are provided in the accessories bag. A blocked cooling system can damage the engine. The engine should be cleaned at least once a year or every hours of operation. Remove the fan casing. Clean the cooling fins on the cylinder, the fan and the rotating protective grille. Clean more frequently if mowing dry grass.

The battery must be fully charged before being used for the first time. The battery should always be stored fully charged. If the battery is stored while totally flat it could sustain permanent damage. If the machine is not going to be used for an extended period more than 1 month , the battery should be charged, disconnected and then stored in a cool, safe place. Charge the battery completely before reinstalling.

The battery can be charged in two ways: 1. Via a battery charger recommended. This must be a charger with constant voltage. The battery can be damaged if a standard type battery charger for acid batteries is used. Stiga recommends battery charger with item no. You can also allow the engine to charge the battery. In this case it is very important, above all when starting the machine for the first time and when it has not been used for a long time, to allow the engine to run continuously for at least 45 minutes.

Sparks occur which can result in fire. Do not wear metal jewellery which can come into contact with the battery terminals. In the event of damage to the battery casing, cover, terminals or interference to the strip covering the valves, the battery should be replaced. If the battery terminals are coated with oxide, they should be cleaned. Clean the battery terminals with a wire brush and grease them. The battery is a valve-regulated battery with 12 V nominal voltage.

The battery is completely maintenance free. Do not tension the steering cables too hard. Otherwise the steering will be heavy and wear and tear on the cables will increase. Stiga Hydraulic Oil Tank. Stiga Hydraulic Pump-Kpl 10Alp. Stiga Hydraulic Tube. Stiga Idler Pulley. Stiga Ignition Key. Stiga Ignition Switch. Stiga Implement Pedal. Stiga Inner Cover. Stiga Inner Panel Bracket. Stiga Inner Steering Tube.

Stiga Inner Tube. Stiga Knob. Stiga Knob Holder. Stiga Lamp Holder. Stiga Lamp Lens. Stiga Led Lamp. Stiga Lever. Stiga Lever Bracket. Stiga Lift Arm. Stiga Lift Catch Assembly.

Stiga Lift Lever. Stiga Lift Pedal. Stiga Link. Stiga Locating Pin. Stiga Locking Pin. Stiga Low Self-locking Nut M8. Stiga Lower Cover. Stiga Lower Front Panel. Stiga Lower Slide Plate. Stiga Lower Steering Tube. Stiga Magnet Clutch. Stiga Muffler. Stiga Nipple. Stiga Nut. Stiga NUT. Stiga Nut Cap M8 [black]. Stiga O Ring. Stiga Oil Drain Assembly. Stiga Oil Tank Cap. Stiga Outer Cover. Stiga Pin.

Stiga Pivot Shaft Stop. Stiga Plastic Button. Stiga Plate. Stiga Plug. Stiga Pneumatic Valve. Stiga Pop Rivet. Stiga Pto Switch. Stiga Pull Rod. Stiga Push on Fixing. Stiga Push Pin. Stiga Quick Coupling-Male. Stiga Rac Quick Connection 4Wd.

Stiga Rear Bumper. For starting cold en- gine. Control pushed in — choke valve open. For starting warm engine and when oper- ating the machine. Also includes switch for spotlight Senator does not have a spotlight. Four positions:. Start position — the electric start motor is activated when the key is turned to the spring-loaded start position. Once the en- gine has started, let the key return to oper- ating position 3. This means that the implement can follow the contours of the ground.

User manuals, Stiga Lawn mower Operating guides and Service manuals. The use of such parts and accessories can affect the function and safety of the machine. A front brake wire and a rear pull bar. If you are still having trouble, try using the search at the top of the page, or get help identifying the correct part … E-mail : info stiga-store. If you require a Stiga part that is not listed, please call with part number or FULL details of Machine, ie.

Model, Type and Serial Number.